Fixed an issue that prevented the camera measuring values for preset white balance when live view photography was selected with the live view selector and Record movies was selected for Custom Setting g4 ( Assign shutter button) in the CUSTOM SETTING MENU.Fixed an issue that resulted in List saved values failing to display the complete list when fine-tuning values 12 or 18 lenses were saved using AF fine-tune > Saved value in the setup menu.- Focus is selected for Custom Setting a2 ( AF-S priority selection) in the CUSTOM SETTING MENU.- Single-point AF is selected for AF-area mode.Previously the shutter could then be released at any time, but under the following conditions this behavior has been changed so that the shutter will not be released if the camera is unable to focus: * If the AF-ON button is used to focus during viewfinder photography when AF-ON only is selected for Custom Setting a4 ( AF activation) in the CUSTOM SETTING MENU, focus will remain locked when the button is released.Added support for CompactFlash memory cards with capacities over 128 GB.Added support for UT-1 communication unit firmware updates.Note that after updating the camera firmware you will no longer be able to use network and connection settings created with earlier versions and must adjust settings for connection again. The foregoing features require UT-1 firmware version 2.0 or later and version 1.5.0 or later of the Wireless Transmitter Utility.- “PC mode” is now “Camera control” and is used with optional Camera Control Pro 2 software to control the camera remotely and save photos and movies to a computer.- “Transfer mode (PC)” is now “Image transfer” and is used to upload photos and movies from the camera memory card to a computer immediately after shooting.- “Transfer mode (FTP)” is now “FTP upload” and is used to upload photos and movies from the camera memory card to an ftp server immediately after shooting.- HTTP mode: The contents of the camera memory card can be viewed and photos taken remotely from a computer or iPhone using a web browser.A Network (UT-1) option has consequently been added to the setup menu and the Wireless transmitter option in the setup menu has been renamed Wireless transmitter (WT-4). Added or renamed features for use with the UT-1 communication unit firmware version 2.0.Added an Assign remote Fn button at Position f15 in the CUSTOM SETTING MENU. *.With the addition of Assign movie record button at Position f13 in the CUSTOM SETTING MENU, the Assign MB-D12 AF-ON option in the CUSTOM SETTING MENU has been reassigned to Position f14.Added Assign movie record button at Position f13 in the CUSTOM SETTING MENU. *.- When photos were taken using Camera Control Pro 2 after Custom Setting d10 ( Exposure delay mode) was enabled in the CUSTOM SETTING MENU, the software would sometimes mistakenly display a message stating that no photo could be taken.Ĭhanges from Previous Versions Changes from Firmware “A” Version 1.01/“B” Version 1.02 to “A”/“B” Version 1.10.- When focus is adjusted by rotating the lens focus ring, the focus indicator in the viewfinder (and in live view, the focus point in the monitor) now flash to indicate when infinity or the minimum focus distance is reached.- If the standby timer expires after focusing, the focus position will no longer change when the timer is reactivated.Added the following supports for AF-P lenses:. Settings saved with firmware “A” version 1.01/“B” version 1.02 or earlier are not compatible with D800 “A”/“B” firmware version 1.10 or later.Ĭhanges from “A”/“B” Firmware Version 1.10 to Version 1.11 Do not attempt to load settings saved using Save/load settings for firmware “A” version 1.01/“B” version 1.02 or earlier onto a D800 with “A”/“B” firmware version 1.10 or later.Before proceeding with the update, users of Lexar 400× and 1000× CompactFlash ® memory cards will need to follow the steps here to check compatibility.Read the information below before proceeding.You will not need to download or install this update if the firmware listed above is already installed. Before proceeding, select Firmware version in the camera SETUP MENU and check the camera firmware version. The update can be performed on both the “A” and “B” firmware simultaneously.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |